In this video, we take a look at the all new ODROID HC4 Single Board computer/NAS/HOME Cloud Platform!
The HC4 has some pretty neat feathers built-in like dual SATA drive connectors running over a PCIe to SATA direct bridge. This board can be used as a Home Cloud Platform, PLEX server, Open Media Vault, Desktop PC, or even a retro gaming device and it can also run Android!
Powered by the Amlogic S905x3 CPU and backed by 4GB of LPDDR4 ram just like the ODROID C4 so the possibility is endless!

Learn More Here: https://www.hardkernel.com/shop/odroid-hc4/
Buy on on Amazon: https://amzn.to/37BxHSM

Specifications
FORM FACTOR Board Dimensions: 84mm x 90.5mm x 25.0mm
Heatsink Dimensions: 40mm x 32mm x 10mm
Weight: 280g including heatsink, fan and case
PROCESSOR Amlogic S905X3 Processor
L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processorsQuad-Core Cortex-A55 (1.800GHz)
ARMv8-A architecture with Neon and Crypto extensions
Mali-G31 MP2 GPU with 4 x Execution Engines (650Mhz)
MEMORY DDR4 4GiB with 32-bit bus width
Data rate: 2640 MT/s (PC4-21333 grade)
1.2Volt low power design
STORAGE 1x Micro SD slot (DS/HS mode up to UHS-I SDR104)
NETWORKING 1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)
– Realtek RTL8211F (Ethernet transceiver)
– LED indicators
* Green LED: Flashing by data traffics at 100Mbps connection
* Amber LED: Flashing by data traffics at 1000Mbps connection
VIDEO 1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
AUDIO 1 x HDMI digital output
COOLER 1 x Passive heatsink ( 40x32x10 mm ) on the CPU of PCB board
1 x Hydraulic Bearing FAN
– Rated Voltage : 5V
– Rated Current : 100mA
– Max Speed RPM : 4,000
– Air Flow CFM : 4.3
– Air Pressure (In H2O) : 0.053
– Noise Level(dBA) : 23.9
– Dimension : 40 x 40 x 10.6 mm
– Wire & Connector : 80mm, 4 pin 1.25mm pitch
EXTERNAL I/O 1 x USB 2.0 host port
1 x Debug serial console (UART)
2 x SATA Connectors
OTHER FEATURES IR receiver for remote controller
System LED Indicators:
– Red (POWER) – Solid light when DC power is connected
– Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
POWER 1 x DC jack : outer (negative) diameter 5.5mm, inner (positive) diameter 2.1mm
DC input : 14.5V ~ 15.5V
– DC 15V/4A power adaptor is recommended. Sold separately.
Power consumption with two ST2000DM006 HDDs :
– IDLE(with HDD in spin-down) : ≃ 5.88W
– Active(using SAMBA): ≃ 15.59W
– Suspend: ≃ 0.29W

Follow Me On Twitter: https://twitter.com/theetaprime
Follow Me On Instagram: https://www.instagram.com/etaprime/

Equipment I Use:
Screen Capture Device: https://amzn.to/2STpX4C
Tool Kit: https://amzn.to/2M6l9WS
Soldering Station: https://amzn.to/2FtdVeu
Camera: https://amzn.to/2M6KFLB
Tripod: https://amzn.to/2CmdYVY
Raspberry Pi 4: https://amzn.to/3cCrvKb
Flirc Case: https://amzn.to/2OBQTXz

DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission at no extra cost to you!

This video and Channel and Video are for viewers 14 years older and up. This video is not made for viewers under the age of 14. If you are under 14 years of age, you do not have permission to view this video.

Want to send me something?
ETAPRIME
12520 Capital Blvd Ste 401 #108
Wake Forest, NC 27587 US

THIS VIDEO IS FOR EDUCATIONAL PURPOSES ONLY!

#ODROID #HC4 #ETAPRIME

source